SWISH helendav kõnepult
SWISH helendav kõnepult ei ole oma välisemuselt vaid eksklusiivne disainiobjekt, vaid ka funktsionaalne ja kergesti ümberpaigutav toode.
SWISH on kasutatav ka menüüalusena.
Tehke julgelt broneerimistellimus, vaatame selle üle ja võtame Teiega ise ühendust! Peida
Näitan 801–900 tulemust 923-st


SWISH helendav kõnepult ei ole oma välisemuselt vaid eksklusiivne disainiobjekt, vaid ka funktsionaalne ja kergesti ümberpaigutav toode.
SWISH on kasutatav ka menüüalusena.

The XES-2T6 is a six plus two port Gigabit Ethernet switch with two ports being aggregated to a high throughput, redundant trunk link. The six other ports are individually assignable to groups (IEEE 802.1Q VLANs) that may participate in completely independent networks that do not interfere with each other. Thanks to the graphic OLED display, the encoder knob and a push button for each of the six configurable ports, the switch is intuitive to setup and the configuration is done in next to no time.
The grouping and the redundant fast backbone link make the XES-2T6 an ideal solution for interconnecting the stage with the FOH for instance.
As a layer 2 switch, the XES-2T6 is generally unaware of the application and therefore it works well with any protocol that operates on top of TCP/IP and with many Ethernet based protocols. However, special precautions have been taken to ensure that the XES-2T6 works perfectly with Art-Net, sACN and Dante. The Art-Net specification for example expects the controller to only send data every few seconds or when an update is available. A typical switch might put itself into sleep mode when no traffic is observed, not so the XES-2T6; it stays ready to forward data anytime without delay.
With the increased acceptance of TCP/IP and Ethernet based protocols, the proper operation of the network and its equipment has become critical for many shows. Therefore, it is crucial to professionally plan, configure and install the network for any show or venue. As a measure to further lower the chances of network outages, the XES-2T6 comes equipped with two separate switch mode PSUs that can be powered from two different mains supplies.

Recorded Channels 512 channels.
Storage Capacity Due to a very sophisticatedDMX data compression ther is no fixed storage capacity.
The more DMX channels are changing their value, the faster the memory would be full.
Number of sequences 32 different sequences can be recorded.
Link up sequences Number of repeats and “action on end”.
DMX termination 120Ohm built in.
Input Power 50VAC – 276VAC 50/60Hz 0.3A
Operating temperature -0°C to 45°C

The XRC-200 is an easy to use DXM recording and replay unit. The operating concept is similar to a CD player and can be used by non-professionals.
The sequences are recorded from a lighting console, or other DMX output device, onto the device. The XRC-200 replays the recorded sequences in real time.
With the ability to record 2 DMX universes (1024 DMX channels), the XRC-200 is also suitable for LED and moving light applications/installations. A variety of applications in architecture and entertainment, tradeshow, retail and museum lighting are covered with the XRC-200 easily and economically.
The optional XRC-CT15B contact box with 15 inputs for dry contacts allows a customized integration of triggers for control of the XRC-200 in. In addition, the XRC-200 has an internal timer for show and device control. The device can also be set up to be remotely operated or triggered by DMX. During live shows, the XRC-200 can be used as a DMX backup device.
The sequences and settings of the XRC-200 can be stored and managed with the XRC-200 PC software, which is connected via the USB port.


XSP-5B DMX 5way DMX Splitter & Booster Box with XLP 5pin Connectors. Suitable for Desk Top and Truss Mounting. Supplied with M10 Threaded Socket (max 20mm) and Eye for Safety Bond.








Polüetüleenist valmistatud mahutid on sobilikud väikese koguse kütuse transportimiseks ja tankimiseks. Sobilikud bensiinile ja diislile. Mugavat ja kiiret tankimist tagab Emmillcaddy tankur, mida on võimalik soetada nii elektrilise- kui ka käsipumbaga. Tankurit soovitame mitme ahju kasutajale. Tankurit on mugav tankida ja transportida kaubabussi põrandal selili. Tänu heale kaalujaotusele on täidetud tankurit hea järel vedada ja liigutada. Püstolil on automaatne lukusti juhuks, kui tankimisel pakk on täis saamas. Lisana on võimalus soetada imusüsteem, millega on vajadusel võimalik ahju paak tühjaks tankida tagasi tankurisse.
Tankurile sobib Makita aku 18V (aku ja laadija ei sisaldu hinnas)


The Squeez SQ-2 from Tapco is a dual channel compressor with gating and a single band, adjustable “Air” EQ. The EQ can be used for obtaining the classic vocal sound of the 60s and 70s, or for replacing high frequency content due to heavy compression. Inserts on both channels allow for frequency sensitive compression.
The compressor section offers both auto “soft-knee” and “hard-knee” curves, while the gate employs “soft” operation and an expander function at the threshold to eliminate clicks from drums and other percussive sounds.
The unit provides dedicated threshold and ratio controls along with attack and release controls for the compressor, an output control that allows for volume make-up and eight LEDs on each channel display gain reduction. An automatic attack/release button is provided for those that prefer ease of use, or are unfamiliar with the subtleties of compression.
Dual channel compressor with gate.
Auto Soft-Knee/Hard-Knee curves depending on compression setting.
Adjustable “Air” filter adds natural high-end for “classic” studio compression sounds.
Soft Gate circuitry provides expansion at the threshold to eliminate clipped gated sounds.
Individual threshold, ratio, attack and release controls per channel.
Auto attack/release function with indicator.
Output gain compensation controls.
Individual Channel In/Out button and indicator.
Precision eight-segment gain reduction meters.
Side chain connections for frequency-sensitive compression such as de-essing.


The HS-20 is a professional two-channel recorder/player that is capable of uploading and downloading files to/from servers via an FTP client function.
Event lists for recording, playback, and downloading aligned with time-based management are perfect for scheduled playback scenarios such as BGM and in-store announcements.
Through the combination of event lists with the FTP client function, users can easily create a system in which files uploaded onto the server at headquarters can be automatically distributed and played at different store branches.
After completing a recording, the HS-20 can automatically upload the recorded data to a designated server.
Various applications can be performed by combining this automatic upload function with recording/downloading events; for instance, users can automatically upload files from a scheduled recording onto the server, with the files being automatically retrieved from the server for playback or archiving.
The SNTP client feature automatically adjusts its internal clock via the internet, meaning that recording, playback, downloading, and other events can be executed at accurate, synchronized times.
The recording/playback format supports BWF/WAV (playback only) and 192kHz/24bit high-resolution recording/playback. SD/SDHC cards and CF cards are used for memory media.
The recording playback unit possesses a high level of durability that does not require maintenance due to its lack of moving mechanisms.
The HS-20 is a professional recorder/player with an integrated professional stereo recorder/player that is high in both sound quality and durability.
Equipped with network functions, the HS-20 can perform recording, playback, downloading and various other events automatically.


New from TASCAM, the MD-CD1 combines CD playback and MiniDisc recording in a single rackmount unit designed to save rack space and installation budgets. Like all of TASCAM’s products designed for fixed installation, the MD-CD1 is a reliable player designed for years of trouble-free use. The unit is stocked with features, such as 12% pitch control, MP3 CD playback, RS-232 control and an optional balanced I/O board that allow it to be spec’d into a wide variety of applications.
The TASCAM MD-CD1 has a host of professional features like RS-232 control, digital I/O and an optional I/O board for balanced interfacing. CDs can be played back at up to 12% higher or lower, and can even be played back faster without changing the pitch for a “chipmunk” effect. Discs can be duplicated from CD to MiniDisc at up to 4x speed, and a wireless IR remote is included.


he MH-8 is the ideal headphones amplifier for studio, stage and installation. Each of the eight stereo outputs delivers 250 mW per side with three switchable sources available. Two stereo inputs can be shared to any of the outputs, and individual stereo direct inputs are available for each of the eight channels. A headphones channel can use any one of these inputs, or mix several together. And a set of foldback outputs allows the user to chain other MH-8s into a system.
The MH-8 is housed in a rugged, rack-mountable metal chassis with built-in power supply (no AC adapter), ground terminal and ground-lift switch for many years of safe and reliable operation.


Stereo Audio Meter with 7″ High Resolution Display and USB Connection for Plug-In Metering.

Ultimate Multi-Tap Rhythm Delay Unit with Flexible Control.
TC quality delays and effects.
Multitap rhythm delay.
Absolute repeat control.


Dual-Engine Signal Processor with High-Quality Reverb and Multi-Effects for Live or Studio Applications.


These industry standard turntables are simply the best and what pro DJs insist on. We have one pair that are also available with a variety of DJ mixing desks.
Technics SL series turntables have become legendary with over 3 million sets being produced and used by DJs and clubs the world over. All SL models feature the undisputedly accurate, reliable and durable Quartz Direct Drive Motor, with Aluminium Diecast cabinets and heavy rubber base for vibration damping.
The SL1210MK5 has the same dependable construction as the famous and record selling SL1210MK2 with the addition of 0.6g Anti Skate (0.3g on the SL1210MK2), Adjustable Brake Speed accessed from just beneath the platter, continuous pitch shift with a reset control for 100% precision and finished off with a Long Life White LED Stylus Light. Technics black finish.

Master Sync/Master Clock Reference Generator.
The SPG8000A is a precision multiformat video signal generator, suitable for master synchronization and reference applications. It provides
multiple video reference signals, such as blackburst, HD tri-level sync,
and serial digital and composite analog test patterns, and it provides time
reference signals such as timecode, NTP (Network Time Protocol) and
IEEE 1588 Precision Time Protocol (PTP).

Mobile module 4G LTE Cat 4 up to 150 DL/50 UL Mbps; 3G up to 21 DL/5.76 UL Mbps; 2G up to 236.8 DL/236.8 UL kbps 3GPP Release Release 10/11 depending on the hardware version SIM switch 2 SIM cards, auto-switch cases: weak signal, data limit, SMS limit, roaming, no network, network denied, data connection…

Motherdrum, also Indian Pow-wow drum or Earthdrum. This drum is the mother of all bass drums. Can be played by 5-8 people with different mallets at the same time Used in therapy Diameter: 100 cm Detachable stand made of natural wood Cowhide drum head (significant deviations in appearance possible) Bag and one pair of mallets…


120° tilting angle Dual spigot 16mm (5/8″) receiver Ratcheted “L” handle Fully metal made Grip type: Holder Mounting: Receiver 16mm Color: Black Material: Aluminum

Toca’s Barrel Conga Stands are crafted from sturdy-yet-lightweight steel, and are finished with a black powder coating for a professional look. Thick, soft padding is attached at the point of contact with the drum, preventing physical damage and eliminating rattles. This stand will hold any conga from 25 to 28 cm.


Soundproofings Our booths meet the ISO4043 standard by offering higher levels of soundproofing than the levels minimum required. Total weight: 122 kg 2 standard panels: 10 kg 1 reinforced standard panel: 13 kg 3 Glazed panels: 13 kG 1 reinforced Glazed panels : 17 kg 1 Door panel: 15 kg 2 Roof panels: 8 kg…

TOP-BRACKET-QTB Top Bracket for mounting lights on truss or on the floor.

TOP-RING-QTB-D1000 M290 top circle with 1m diameter Diameter: 1000 mm.

Ethernet Switch Type: Unmanaged Mounting Type: Desktop Ports: 5 RJ45 Ports: 5 Network Speed: 1 Gbps Series: LS Operating Voltage Max. – DC: 5 V Operating Temperature Min.: 0 °C Operating Temperature Max.: 40 °C


Trace Elliot Speed Twin (EL84 based) C30 30-Watt combo, dual channel, loaded with a Celestion GT12-75 75-watt speaker.


Installers and integrators can save on equipment costs and reduce installation time with TRENDnet’s Unmanaged Gigabit PoE+ Switches. These unmanaged PoE+ switches deliver up to 30W per port of PoE power and data over existing Ethernet cables. With PoE technology, users only need one set of cables to deliver both data and power. With this unmanaged PoE+ switch, network PoE and PoE+ devices, such as high-power wireless access points, PTZ and other advanced IP cameras, VoIP phone systems, IPTV decoders, access controls, and more.



he Wentex Truss Sleeve is a versatile accessory used at events and exhibitions to dress trusses and create lighting effects. Dressing trusses with sleeves offers aesthetic benefits, allowing event planners to create a clean and cohesive look, hiding the metal frame and creating a unified design. One of the main advantages of using a Truss Sleeve is its ease of use. The stretchy material allows for a snug fit, ensuring the sleeve stays in place throughout the event.
Our Truss Sleeve is permanently flame retardant according to DIN 4102 B1. It is made from 100% PES FR (fire retardant polyester) and can be washed while retaining its flame retardant properties. Use a delicate wash cycle at 30° maximum and a mild, phosphate-free detergent. Iron at max. 110° and be careful with steam!

he Wentex Truss Sleeve is a versatile accessory used at events and exhibitions to dress trusses and create lighting effects. Dressing trusses with sleeves offers aesthetic benefits, allowing event planners to create a clean and cohesive look, hiding the metal frame and creating a unified design. One of the main advantages of using a Truss Sleeve is its ease of use. The stretchy material allows for a snug fit, ensuring the sleeve stays in place throughout the event.
Our Truss Sleeve is permanently flame retardant according to DIN 4102 B1. It is made from 100% PES FR (fire retardant polyester) and can be washed while retaining its flame retardant properties. Use a delicate wash cycle at 30° maximum and a mild, phosphate-free detergent. Iron at max. 110° and be careful with steam!






The TX2-Stage is a bidirectional transmitter of the X2-series, used to control receivers either via manual ignition signals, the AutoMode, or PC-Mode. Thanks to its small size it is especially well suited for smaller outdoorshows, stage pyrotechnics, or as a backup transmitter.


Suure võimsusega professionaalne kunstlumemasin. See võib luua nii vaikset romantilist lund kui ka hämmastavaid lumetormiefekte, hoides samal ajal oma töömüra väga madalana, muutes selle suurepäraseks keskkondades, kus on vaja vaikust. 1-100% täpsusega reguleeritav väljundi võimsus ja ventilaatori kiirus täiusliku visuaalse efekti saavutamiseks. Täiustatud pumba ja PCB-ga masinal on rikete võimalus viidud miinimumini. Kaasasolevat kinnitusklambrit kasutatdes saab seadme riputada trussiraami külge. Kõrgemale paigaldamine tagab naturaalse ning tõelise langeva lume efekti koos lumerätsakute kukkumise ja triivimisega.


The UNI BAR is a new very compact single DMX dimmer for truss or stands. It’s very lightweight and with 10A max powerful to run big flooters or PAR cans. The dimmer preset and limit functions are great for a long lifetime of your lamps. You may mount the UNI BAR with standard truss clamps or couplers.

The UE Snow Tube Standard is a snow machine using air compression but no pump. It creates a realistic snow effect using air and can propel snowflakes of varying size over a distance of 12m.
It is compact, low noise and very reliable and can be used on the floor or hung up. It is adapted to live shows, concerts, theatres and TV. This snow machine is supplied with its support, a 5L drum and remote quick couplings. Professional connection system and resettable fuse.
Made from ALUMINIUM and STAINLESS STEEL, the UE Snow Tube Standard is a durable product. Each component was selected keeping in mind its quality and its efficiency.






Dekoratiivsete Aafrika stiilis vaaside / pottide komplekt.

The UE Foam Tube is a compact, silent and very efficient foam machine thanks to its high technology centrifugal fan. It quickly creates It creates a quick foam effect for small scale events. It is totally adapted to theatres, opera houses and TV.
This foam machine can be directly connected to the water supply using an automatic mixer, through a venturi suction system. It comes complete with its support, a 5L drum, 2 pipes (10 and 15 m) and a quick coupling to connect the machine to the water supply. Professional connection system and resettable fuse.
Made from aluminium and stainless steel, the UE Foam Tube is a durable product. Each component was selected keeping in mind its quality and its efficiency.


Elutruude, veinipunaste lehtedega valged kaunid lilled, pilgupüüdjaks 100 võimast külma tooniga valget LED dioodi õite sees.
4 tk komplektis.

Colorful party fun.
Amaze your guests with a Eurolite disco ball and its colorful light effects! This mirror ball has a diameter of 13 cm, rotates around its own axis with 5 rotations per minute and paints the room in red, green and blue lights.
Plug and play: The mirror ball does not require any preparation. All you have to do is plug it in, the rest works automatically. Thanks to the compact and lightweight design, you can take your new little LED disco with you wherever you go and place it in any location you like. The power adapter required for operation is, of course, included in the delivery.


Komplekti kuulub kokkupandav laud ja 2 kokkupandavat pinki Mõõdud: Laud: 50 x 220 x h 75 cm Pink: 28 x 220 x h45 cm Kaal: 48 kg


The Hellball 3 is a futuristic mirror ball effect with LEDs. With semi-transparent housing and 3x 3W RGB LEDs, it produces wonderful effects. It also has three different operating modes: DMX512, automatic and sound to light mode.

Läbimõõt: 50cm Labad: 3 tk Suund: reguleeritav üles-alla suunal. Juhe: 1,6 m.


Uuenduslik mullimasin, mille sisseehitatud võimas ventilaator suudab pihustada mullid vertikaalselt kuni 4-5 meetri kõrgusele. 5 x 8W RGBA 4-in-1 LED-tulega suudab see luua särav-värvilisi mulliefekte. 1,3-liitrine mullivedeliku mahuti hoiab mullivedelikku lekkekindlalt. Sisseehitatud mullivedeliku kogumisanum hoiab ära mullivedeliku maapinnale tilkumise. Mullide kõrgust ja värvi saab reguleerida ning see sobib kõikjale, kus on soov inimesi rõõmustada seebimullidega.


Barriers with cordons of the highest quality and durability. Discover optimal products for VIP barriers, barriers in museums and for other occasions. Ensure targeted guidance of people and enhance the exclusivity of your venue.


Grip type: Clamp Mounting: Stud 16mm & Hex 16mm receiver Openings: 0-270 mm Max opening: 270 mm Color: Chrome Material: Steel alloy Max opening: 27 cm Aka: Super Viser / Cardellini / Metthellini Clamp or MaxClamp Spigot 16mm tail and hexa 16mm receiver on top Rubber pads to protect surface & avoid slipping Anti-twist grooved…


Helendav pukktool on mitmekülgne ja ergonoomiline disainielement, mis sobib ideaalselt igasse ruumi.





Voltage: 230 Programmable: No Electrician needed: No Power (input) (W): 1500 Heating element: Heater Materials: Stainless steel


Telescopic boom arm: 75 to 130 cm Wall-mounting base plate 16 mm dual mounting spigot Vertical and horizontal rotation Packed length: 75 cm Aluminum construction Telescopic boom arm with wall mount base, ideal for overhead subject lighting. Comes with 4 expansion anchors for mounting the boom arm on load-bearing walls. The boom arm extends from…


Kui päris tuld ja leeki ei saa ega tohi mõnel juhul kasutada on abiks unikaalne Water Mist Flameri seade. Seadet saab kasutada ka õues tänu IP55 kaitseklassile. Seade kasutab veeudu tekitamiseks ultraheli. 64 LED-dioodiga simuleeritakse realistlikku leegiefekti. Väga tugevast komposiitmaterjalist integreeritud korpus on vastupidav ja roostevaba. Seadme lõputu töötsükli tagab automaatse täitmise funktsioon läbi veevõrgu.
Sobilik seade, tekitamaks realistlikku tule-efekti!

WBFC-212F flight-case ensures safe storage and transportation of 1 base station, 8 “EXTREME Series” wireless beltpacks, 2 beltpack chargers and up to 9 headsets*
Compatible beltpack models: WBP-210HD, WBP-212HD, WBP-210HD FL, WBP-212HD FL and previous “EXTREME Series” models. Compatible charger model: WBPC-210
Single earpad models. Maximum capacity may vary when using dual earpad headsets.


Colour: Black Material: Steel Finish: Powder Coating Thread: M10




Colour: Black Material: Steel Finish: Powder Coating Thread: M10





Orange powder coated baseplate pin. Simply connect the pin to the baseplate with the M10 screw (use an Allen-key). Compatible with Pipe and Drape systems.


Orange powder coated baseplate pin, Simply connect the pin to the baseplate with the M10 screw (use an Allen-key).


Orange powder coated baseplate pin. Simply connect the pin to the baseplate with the M10 screw (use an Allen-key). Compatible with Pipe and Drape systems.


Orange powder coated baseplate pin, Simply connect the pin to the baseplate with the M10 screw (use an Allen-key).


Orange powder coated baseplate pin, Simply connect the pin to the baseplate with the M10 screw (use an Allen-key).


Orange powder coated baseplate pin. Simply connect the pin to the baseplate with the M10 screw (use an Allen-key). Compatible with Pipe and Drape systems.


The Wentex Fixed Upright is not telescopic and is part of the Pipe and Drape system. It has a fixed height of 100 cm and is the ideal base in combination with the 30 x 35 cm base plate and 10 cm base plate pin. Equipped with a 4-way adapter, up to four cross bars can be connected effortlessly.


The Wentex Fixed Upright is not telescopic and is part of the Pipe & Drape system. It has a fixed height of 100 cm and is the ideal base in combination with the 30 x 35 cm base plate and 10 cm base plate pin. Equipped with a 4-way adapter, up to four cross bars can be connected effortlessly.
The maximum supported weight is 25 kg. This makes it a perfect tool for hanging curtains and you can use it to hide backgrounds or create partitions. The height of this upright is ideal to serve as a barrier between the audience and the Front Of House.

Dimout fabrics are shiny fabrics with a weight of 260 g/m². They are ideal for decorative applications and available in a wide selection of colours. Dimout curtains are specially designed to block light and can be used e.g. in front of windows. For situations requiring lengths of more than 330 cm, the curtain has a sewn-in 30 cm piece of hook tape at the top that makes it possible to overlap another curtain, ensuring there are no gaps in between. The hook tape can also be used to wrap the curtain around the upright to conceal it. Compatible with Pipe and Drape systems.

Dimout fabrics are shiny fabrics with a weight of 260 g/m². They are ideal for decorative applications and available in a wide selection of colours. Dimout curtains are specially designed to block light and can be used e.g. in front of windows. For situations requiring lengths of more than 330 cm, the curtain has a sewn-in 30 cm piece of hook tape at the top that makes it possible to overlap another curtain, ensuring there are no gaps in between. The hook tape can also be used to wrap the curtain around the upright to conceal it. Compatible with Pipe and Drape systems.

Molton CS is the standard for stage clothing. Molton CS is a relatively thick fabric with a weight of 300 g/m². It has a matt appearance and high light absorption. Due to its higher density, it also blocks light much better than the Medium Gloss Satin. For situations requiring lengths of more than 330 cm, the curtain has a sewn-in 30 cm piece of hook tape at the top that makes it possible to overlap another curtain, ensuring there are no gaps in between. The hook tape can also be used to wrap the curtain around the upright to conceal it. Compatible with Pipe and Drape systems.


The Wentex P&D Curtain MGS (Medium Gloss Satin) is a lightweight curtain with a slightly glossy appearance. Weighing only 175 g/m², it is easy to handle and cost-effective. For situations requiring lengths of more than 330 cm, the curtain has a sewn-in 30 cm piece of hook tape at the top that makes it possible to overlap another curtain, ensuring there are no gaps in between. The hook tape can also be used to wrap the curtain around the upright to conceal it.
Medium Gloss Satin curtains are washable and flame retardant according to EN 13501-1, since they are made of 100% PES FR. Because it is a thin fabric, it does not block light completely. We recommend the Wentex Dimout curtains for such applications. Compatible with Pipe and Drape systems.




Colour: Black Material: Aluminium Finish: Powder Coating Thread: M8


You can rent and buy all sorts of Pipes & Drapes systems, but there is no system as versatile and easy to use as Wentex Pipes & Drapes. As a result of pure innovations, our Pipes & Drapes system is far easier to move around than any other system in the market. It is also very decorative. All that makes it the no. 1 choice for for theatres, events, business premises, exhibitions and many more.
Revolutionary 4-way connector system
If you have used a Pipes & Drapes system before, you probably know what the shortcomings are: for example, telescopic drape support that detach, irregular hanging curtains or clumsy mounting.
The revolutionary and patented 4-way connector with its autolock system makes these occurrences a thing of the past. This system guarantees solid connections of uprights and drape supports while they can still be adjusted to every conceivable direction. Wentex Pipes & Drapes goes ever further. Another advantage is that the four openings of the connectors have a universal size of 16 mm. That gives you room for mounting a camera, speaker or lamp. Using an adapter, you can also link the 4-way connector seamlessly to all Pipes & Drapes systems with round uprights.
Additional advantages
You will discover additional advantages when you use Wentex Pipes & Drapes. Our telescopic uprights made of reinforced aluminium can be assembled up to 6 metres without the need for ladders, and their locking heads guarantee an easy and robust connection. In addition, our baseplates with rounded-off corners are reinforced to bear extra weight.
The reinforced drape supports can bear a weight of 25 kg and they can be adjusted to up to 3 metres in length. The Velcro system guarantees that the curtains are hanging even and straight.
Curtains
All curtains of the Wentex P&D range are made of permanent flame retardant fabrics meeting the German standard DIN 4102-B1. Curtains can be washed while they keep the flame retardancy.
Medium Gloss Satin.
Medium Gloss Satin is a lightweight fabric. Its weight is 165 gram/m². Due to the lightweight it is easy to handle and more cost effective. The curtains have a bit glossy out looking. Medium Gloss Satin curtains can be washed and are flame retardant according DIN 4102-B1 (IFR). They are made of of 100 % PES FR. Because of the light weight fabric it will not block light for 100 % for these kind of applications you can use the Dimout series.
Molton CS
Molton CS is the standard for stage clothing and is made of the same fabric as backdrops. Molton CS is heavy with a 300 gram/m² weight. It has a matt finishing and therefore absorbs most of the light. Due to its higher density it also blocks light much better than the Medium Gloss Satin.
Molton CS curtains are washable and are flame retardant according DIN 4102-B1 (IFR).
They are made of 100 % PES FR.
Dimout
Dimout fabrics are shiny fabrics with a weight of 260 gram/2. They are ideal for decorative applications and available in a wide selection of colours. Dimout curtains are special designed to block light and can be used e.g. in front of windows.
Dimout curtains can be washed and are flame retardant according DIN 4102-B1 (IFR). They are made of 100 % PES FR.
String Curtain
String Curtains are very suitable for decorative effects. They have a high transparency and are ideal to be illuminated to create stylish and impressive effects. String curtains are washable and are flame retardant according DIN 4102-B1 (IFR). They are made of 100 % PES FR.



Molton CS is the standard for stage clothing. Molton CS is a relatively thick fabric. It has a matt appearance and high light absorption. Due to its higher density, it also blocks light much better than the Medium Gloss Satin. At the top left, a 30 cm piece of hook tape is sewn on so that the neighbouring curtain can be attached with a slight overlap. In this way, the curtains completely cover what is behind and do not leave an opening. The hook tape can also be used to wrap the curtain around the upright to conceal it.





Colour: Black Material: Aluminium, Plastic Finish: Powder Coating Rigging Mounting Options: Hook and Loop








The Wentex Telescopic upright is part of the Showtec Pipe and Drape system. This 2-way system is a stepless adjustable upright for hanging drapes with a height of 120 cm up to 180 cm. It is therefore widely applicable.


The Wentex Telescopic upright is part of the Showtec Pipe and Drape system. This 3-way system is a stepless adjustable upright for hanging drapes with a height of 180 cm up to 420 cm. It is therefore widely applicable.


Minimum Height (m): 180 cm Maximum Height (m): 420 cm Diameter: 51 mm (2.008″) Diameter (Inner): 4.6 cm Colour: Black Material: Aluminium, Plastic Finish: Powder Coating

The Wentex Truss Sleeve is a versatile accessory used at events and exhibitions to dress trusses and create lighting effects. Dressing trusses with sleeves offers aesthetic benefits, allowing event planners to create a clean and cohesive look, hiding the metal frame and creating a unified design. One of the main advantages of using a Truss Sleeve is its ease of use. The stretchy material allows for a snug fit, ensuring the sleeve stays in place throughout the event.
Our Truss Sleeve is permanently flame retardant according to DIN 4102 B1. It is made from 100% PES FR (fire retardant polyester) and can be washed while retaining its flame retardant properties. Use a delicate wash cycle at 30° maximum and a mild, phosphate-free detergent. Iron at max. 110° and be careful with steam!


The Wentex Truss Sleeve is a versatile accessory used at events and exhibitions to dress trusses and create lighting effects. Dressing trusses with sleeves offers aesthetic benefits, allowing event planners to create a clean and cohesive look, hiding the metal frame and creating a unified design. One of the main advantages of using a Truss Sleeve is its ease of use. The stretchy material allows for a snug fit, ensuring the sleeve stays in place throughout the event.
Our Truss Sleeve is permanently flame retardant according to DIN 4102 B1. It is made from 100% PES FR (fire retardant polyester) and can be washed while retaining its flame retardant properties. Use a delicate wash cycle at 30° maximum and a mild, phosphate-free detergent. Iron at max. 110° and be careful with steam!


Mechanical Specifications Fabric: Polyester Colour: Black Product Properties Washable: Yes


Length: 60 cm Length: 60cm Width; 60 cm Width: 60 cm Height: 0.5 cm Height: 0.5 cm Weight: 14 kg ( Finish: Powder Coating Colour: Black




Maximum Load: 32 kg Colour: Black Material: Aluminium Finish: Powder Coating


Wintel W8 Pro Mini PC CX-W8 Pro TV Box Windows10 Intel Aotm Z8350 Quad-core 2GB RAM 32GB ROM WiFi Bluetooth 4.0.

TY-1500HD Switcher Control Panel Vmix Video Recording 4K Virtual Studio Recording Switcher for Live Broadcast Production New Media YouTube Ins.